仅对英特尔可见 — GUID: nik1410564937566
Ixiasoft
3.1. Avalon-ST RX接口
3.2. Avalon-ST TX接口
3.3. TX信用接口(TX Credit Interface)
3.4. TX和RX串行数据
3.5. 时钟
3.6. 功能级复位接口(Function-Level Reset (FLR) Interface)
3.7. SR-IOV的控制阴影接口(Control Shadow Interface for SR-IOV)
3.8. 配置扩展总线接口(Configuration Extension Bus Interface)
3.9. Hard IP重配置接口
3.10. 中断接口
3.11. 电源管理接口(Power Management Interface)
3.12. 复位(Reset)
3.13. 传输层配置接口
3.14. PLL重配置接口
3.15. PIPE接口(仅适用于仿真)
6.1.1. Avalon-ST RX和TX接口的TLP Header和Data对齐
6.1.2. Avalon-ST 256-Bit RX接口
6.1.3. Avalon-ST 512-Bit RX接口
6.1.4. Avalon-ST 256-Bit TX接口
6.1.5. Avalon-ST 512-Bit TX接口
6.1.6. TX信用接口(TX Credit Interface)
6.1.7. 解释TX信用接口(Interpreting the TX Credit Interface)
6.1.8. 时钟
6.1.9. 更新流程控制计时器和信用释放(Update Flow Control Timer and Credit Release)
6.1.10. 复位(Resets)
6.1.11. 功能级复位接口(Function-Level Reset (FLR) Interface)
6.1.12. 中断
6.1.13. SR-IOV的控制阴影接口(Control Shadow Interface for SR-IOV)
6.1.14. 传输层配置空间接口(Transaction Layer Configuration Space Interface)
6.1.15. 配置扩展总线接口(Configuration Extension Bus Interface)
6.1.16. 硬核IP状态接口(Hard IP Status Interface)
6.1.17. 串行数据接口
6.1.18. PIPE接口
6.1.19. Hard IP重配置
6.1.20. 功耗管理接口(Power Management Interface)
6.1.21. 测试接口
6.1.22. PLL IP重配置
6.1.23. 消息处理(Message Handling)
8.1.1. 寄存器访问定义
8.1.2. PCI配置头(header)寄存器
8.1.3. PCI Express性能结构
8.1.4. Intel定义的VSEC Capability头
8.1.5. 通用控制和状态寄存器(General Purpose Control and Status Register)
8.1.6. 不可纠正的内部错误状态寄存器
8.1.7. 不可纠正的内部错误掩码寄存器
8.1.8. 可纠正的内部错误状态寄存器
8.1.9. 可纠正的内部错误掩码寄存器
8.1.10. SR-IOV虚拟化扩展功能寄存器地址映射(SR-IOV Virtualization Extended Capabilities Registers Address Map)
8.1.10.1. ARI Enhanced Capability Header
8.1.10.2. SR-IOV增强性能寄存器(SR-IOV Enhanced Capability Registers)
8.1.10.3. 初始VF和总共VF寄存器(Initial VFs and Total VFs Registers)
8.1.10.4. VF Device ID Register
8.1.10.5. Page Size Registers
8.1.10.6. VF基地址寄存器(BARs) 0-5 (VF Base Address Registers (BARs) 0-5)
8.1.10.7. Secondary PCI Express Extended Capability Header
8.1.10.8. 通道状态寄存器(Lane Status Registers)
8.1.10.9. Transaction Processing Hints (TPH) Requester Enhanced Capability Header
8.1.10.10. TPH Requester Capability Register
8.1.10.11. TPH Requester Control Register
8.1.10.12. Address Translation Services ATS Enhanced Capability Header
8.1.10.13. ATS Capability Register and ATS Control Register
9.4.1. ebfm_barwr处理过程
9.4.2. ebfm_barwr_imm过程(ebfm_barwr_imm Procedure)
9.4.3. ebfm_barrd_wait处理过程
9.4.4. ebfm_barrd_nowt处理过程
9.4.5. ebfm_cfgwr_imm_wait过程(ebfm_cfgwr_imm_wait Procedure)
9.4.6. ebfm_cfgwr_imm_nowt处理过程
9.4.7. ebfm_cfgrd_wait处理过程
9.4.8. ebfm_cfgrd_nowt处理过程
9.4.9. BFM配置过程
9.4.10. BFM共享存储器访问过程
9.4.11. BFM日志和消息过程
9.4.12. Verilog HDL格式化函数
仅对英特尔可见 — GUID: nik1410564937566
Ixiasoft
7.1. 端点的中断
Intel® Stratix® 10 Hard IP for PCI Express支持PCI Express MSI,MSI-X和传统中断(当在Endpoint模式下配置时)。MSI与传统中断是互斥的。上电后,Hard IP模块在传统中断模式下开始。然后,软件决定是否切换到MSI或MSI-X模式。要切换到MSI模式,软件将MSI Message Control Register的msi_enable比特设置成1,(bit[16] of 0x050)。通过使用参数编辑器开启PCI Express/PCI Capabilities选项卡下的Implement MSI-X使能MSI-X模式。如果开启Implement MSI-X选项,那么您应该在BAR指向的存储器空间中实现 MSI-X表结构。
注:
请参考 PCI Express Base Specification的Section 6.1来了解对Endpoints的PCI Express中断支持的总体说明。